Automatic Paging Machine

The technology of heating sealing the aluminum plastic multiplex material by electromagnetic induction is the advanced and popular sealing technology of the world. The electromagnetic induction sealing machine manufactured of this principle is becoming the necessary equipment of medicine, pesticide, axunge, byproduct, health-care, cosmetic, chemistry and other trade requires high quality air sealing for plastic, glass and other non-metal bottle. To improve the level of the product, the sealing and quality-protection function, anti-pirate and anti-forgery.

¡¡

1.  Input power£ºAC110V¡À10%, 60Hz

2.  Input current£º<10A

3.  Output power£ºstatic state <2A, dynamic state <7A

4.  Working frequency£º75-85KHz

5.  Output power£º¡Ü1500W

6.  Enclosure protection grade£ºIP21

7.  Sealing diameter£º¦µ20mm¡«¦µ50mm

8.  Height of the bottle£º1.57~7.87inch (40¡«200mm)

9.  Sealing speed£º0-10m/s (electric stepless speed regulating)

(Note: the speed differs according to the size and material of the sealing object. Using the polythene bottle¦µ31mm,height¦µ38mm as the proof is 250p/s)

10.  Bearing load of the transportation station£º¡Ü44LB (20Kg)

11.  Size£º45.27"*18.89"*15.75" (115cm¡Á48cm¡Á40cm)

12.  Weight of the whole machine£º83.7LB (38Kg)

¡¡

1. Get through 110v power supply; turn on the switch, the power supply meter will display the current voltage, start the cooling device, 3 seconds later, the main circuit begins to work, push the induction switch to start sealing debugging operation.

Caution: continuously and quickly turn on and turn off the power switch is forbidden!! You have to wait at least 5 seconds after turning off the power (the index on current meter disappears) to restart it; otherwise the main circuit of the equipment will be ruined.

2. Adjust the clearance (2¡«5mm) between induction bottom and the upper level of the object sealed and the width to guiding guard bar (the center of the object sealed should focus on the center of the induction, otherwise part of the sealing is not firm), to let it pass.

3. According to the caliber of the object sealed, adjust the initial appropriate speed for sealing transportation. For example, the caliber is small, the spacing is small and the speed is slow, contrarily, the caliber is big, the spacing should be widened and the speed should be quickened.

4. Close the induction switch, put the aluminum foil induction film (the aluminum foil face to the mouth of the bottle, and the paper gasket face to the cover of the bottle) and the object with bottle screwed down on the transportation belt for trial sealing. Adjust the spacing and the transporting speed according to the requirements of 6.2 and 6.3. When the bottle is transported our form the other side of the transportation belt, open the cover of the bottle and check the quality of the sealing, continuous operation can be carried out after the quality reach the requirement.

5. In order to keep the sealing in best working state, find out the best technology parameter and record it by sealing technology tests. To avoid the incautious change in normal manufacture should always check the surface of the sealed cover bottle by hand to see if there is heat after debugging. If there is no heat, should immediately stop the machine and examine it, find out the reason, to avoid the products haven¡¯t been induction heating sealed mix with the qualified products.

6. When the working current exceeds 5A, the passing current protection function of the machine will start and the transportation stop automatically. You should increase the spacing between induction head and the object sealed to reduce the working current, and then push the replacement switch before restart the induction switch. After readjust it can go on the sealing operation.

7. When the temperature of the main circuit of the equipment is too high, the overheat protection function will start and the equipment stop, after the temperature become normal, the equipment will start working again.

¡¡

1 set of Automatic paging machine  230146