https://buyyou.net/cbe/data/prd/251/999/998.jpg

Mud test three-piece set(Mud hydrometer + Sand flow meter + Mud viscometer)
http://topseller365.com/data/prd/054/477/1.jpg
http://topseller365.com/data/prd/054/477/15.jpg
http://topseller365.com/data/prd/054/477/6.jpg
http://topseller365.com/data/prd/054/477/7.jpg
http://topseller365.com/data/prd/054/477/12.jpg
http://topseller365.com/data/prd/054/477/22.JPG
http://topseller365.com/data/prd/054/477/16.jpg 
http://topseller365.com/data/prd/054/477/19.jpg
http://topseller365.com/data/prd/054/477/20.jpg

 

NB-1 Mud hydrometer
NB-1 Mud hydrometer is an instrument for the determination of mud weight in g/cm.This hydrometer is a balance with unequal arms. Its lever edge is resting on the seat that can be fixed and mounted on the table. To the left of the lever is a graduated gambit device.The balance of the lever may be indicated by the horizontal bubble at the top of
the lever.

Main technical features of nb-1 hydrometer:
1. The measurement range is 0.96~3 g/cm 3
2. The scale indexing value is 0.0l g/cm 3
3. The capacity of the mud cup is 140cm 3
4. Instrument size :500(length)*100(width)*100(height)mm

Instructions:
1. When using the mud hydrometer, the mud shall be injected into the mud cup
2. Make the cup flush without bubbles
3. Put the lid on gently
4. Brush off excess spilled mud
5. Place the main tool mouth of the lever on the main tool pad of the base
6. Slowly move the weight so that when the bubble is in the center, the lever is horizontal
7. Read the scale shown to the left of the weight (i.e., mud weight).
8. If you need to measure mud gravity of 2~3 g/cm 3, unscrew the balance cylinder cover
9. Put the balancing hammer in
10. Screw the screw cap to measure
11. The instrument should be rinsed and cleaned after use
Check method:
To check whether the instrument is accurate, the mud cup can be filled with distilled water. If the specific gravity measured in the same way is 1, the meter is accurate.If the result is not 1, then the balance cylinder cover of the hydrometer can be unscrewed to increase or decrease the metal particles in the cylinder so that the specific gravity measured is 1.
 
1006 Mud viscometer
Mud viscometer application:
This instrument is used to measure the viscosity of mud, which is expressed in seconds by the time it takes for 500 cubic centimeters of mud to flow out of the standard field viscometer type 1006.

Main technical characteristics of mud viscometer:
1. The diameter of the outlet pipe hole is 5mm and the length is 100mm
2. Water value: 15±0.5s
3. The capacity of the mezzanine measuring cup is 500ml at one end and 200ml at the other end
4. The total weight of all instruments including accessories and mud cylinder is 2.5kg

Brief instructions for use of mud viscometer:
1. Before measuring the viscosity, wash the viscometer with water and put the mud to be tested into the mud mixer
for 1 minute.
2. Pour 500ml and 200ml(700ml) of mud through the sieve in a measuring cup into the viscometer, and block the flow
outlet of the viscometer with your finger to prevent it from flowing out.
3. Measurement: place the 500ml measuring cup under the flow exit, and start the stopwatch when releasing the
finger blocking the exit.
4. When the measuring cup full of 500ml mud flow reaches its edge, stop the stopwatch and record the time of mud
outflow, that is, the viscosity of mud.

Note: it is convenient to hang the viscometer up for experiment.
 
NA-1 Sand flow meter
NA-1 Sand flow meter is suitable for well site or laboratory mud sand content measurement.It is determined by the
change in the volume of the mud filtered through the screen, expressed as a percentage.

Technical specifications for sand content of na-1 type mud:
1. Filter mesh specification: 200 mesh
2. Sand content scale: 0% ~ 15% for each small cell 0.5%, 15% ~ 30% for each small cell 1%
Packing size:57*41*21cm(Aluminum case packing)
Gross Weight:4.55kg
The product comes in blue and green and is shipped at random.
 
Item Included(054477)

Mud test three-piece set*1

You can make order with no worries.
Any concerns just feel free to let us know, we'll reply in 24 hours in normal condition.
Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.