Handheld Pneumatic Strapper

This tool is a kind of fusion packaging machine. The lapped thermoplastic packaging belt is fused by the heat produced by friction motion; hence, it is called "friction fusion". Principle is to use the binding tape winding product or package, then tighten and ends by heating molten or use the material such as bag buckles connection machine.

Product parameter:

http://topseller365.com/data/prd/151/030/016.jpg

Drived::	by air pump
Size:	113.547.08in(28918cm)
Air pressure:	0.5-0.8Mpa
Max strap tension Max：	3500N
Strapping material:	Polyester
Applications:	PET strap, PP band
Function:	Tensioning+Sealing+Cutting
Strapping width:	13mm(1/2")-19mm(3/4")
Strapping thickness：	0.5(0.0196")-1.5mm(0.06")
Weight：	3.8kg(8.37lb)

Product Analysis：

http://topseller365.com/data/prd/151/030/014.jpg

http://topseller365.com/data/prd/151/030/015.jpg

Feature:

The lightweight body makes the use of equipment more convenient and greatly improves safety performance.

Humanized handheld design
Portable handheld design, convenient for carrying out, suitable for packaging large objects.

http://topseller365.com/data/prd/151/030/023.jpg

http://topseller365.com/data/prd/151/030/114.jpg

Gas pipe quick connect connector

The air pipe must be connected to the air pump for gas supply. The packaging joint is a metal type, wear-resistant, and has a long service life.(Red is the protective cover)
　

Easy packaging operation

Press and hold the tension button with your right thumb until the packaging tape is completely tightened, and then press and hold the fusion button until the packaging tape blows.

http://topseller365.com/data/prd/151/030/022.jpg

Silencing device

In order to keep the machine quiet during operation, this machine is equipped with special noise reduction equipment (note: after the air pump is filled with air, the machine is used without noise).

Rewind button

After packaging is completed, press the rewind button with your right little thumb until the packaging belt is sent down from the tensioning wheel, and then remove the packaging machine.

http://topseller365.com/data/prd/151/030/025.jpg

Principle of Friction Instruction:

1.The compressed air will push the piston within air cylinder. The upper part of piston and vibrating bar is connected with the rocking pin, so the vibrating bar will press the lapped part of packaging belt when moving down.

2.There is an elliptic hole at the center of vibrating bar. This hole is connected with the eccentric shaft of pneumatic motor. The pneumatic motor rotates at a high speed (10000rpm), so the vibrating bar conducts reciprocal motion quickly. The lower part of packaging belt is fixed by the peg teeth of fusion toothed plate, and its upper part is driven by the peg teeth of vibrator for strenuous friction. Hence, the lapped part of packaging belt is fused by the heat produced by friction. When the vibration timer reaches the set time, vibration stops and fusion completes.

3.Both upper and lower parts of the packaging belt are stuck while extruding.

Gas Source Instruction:

Requirement of air pressure
The required scope of air pressure: (5.0-7.0bar)
Installation of gas source
Filter, pressure regulating valve and lubricator assembly shall be close to the pneumatic tool. The min. inner diameter of air hose is 6.0mm(1/4). Both ends of air supply pipe should be equipped with quick unions.
Moisture filtration
A drain valve must be mounted at the bottom of the air supply circuit's bypass to drain once every day.
Lubrication
Pneumatic motor should be lubricated properly, and the lubricator should be full and well regulated (a drop every 2min).

http://topseller365.com/data/prd/151/030/021.jpg

Product safety precautions:

To ensure safe production, please read the following precautions carefully:
　

1.Bear in mind "safety-foremost" principle, and operate this pneumatic tool properly;

2.Read the Manual carefully before operation;

3.Don't dismantle safety parts of the tool;

4.Don't tear or damage label or mark of the product;

5.Don't put hand or other part of your body between packaging belt and packaging tool.

Details:

http://topseller365.com/data/prd/151/030/117.jpg

http://topseller365.com/data/prd/151/030/112.jpg

Product display:

http://topseller365.com/data/prd/151/030/09.jpg

http://topseller365.com/data/prd/151/030/027.gif

Item include：Handheld Pneumatic Strapper*1

Item Number: 151030

You can make order with no worry.
Any concerns just feel free to let us know, we'll reply in 24 hours in normal condition.
Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.