Small Portable Portable Electric Bending Machine
http://topseller365.com/data/prd/190/252/1.jpg
http://topseller365.com/data/prd/190/252/13.jpg
　

Pay attention

1. The steel bars must be placed in a horizontal position. After 40-50 continuous bends, please cool them before use (please combine the actual use conditions, such as weather, machine temperature, etc.).

2. After every 300~500 times of bending, tighten the bolts and screws, especially the bolts of the sealing part between the tool holder and the cylinder block.

　

http://topseller365.com/data/prd/190/252/2.jpg

warn:

　

1. Do not bend steel bars in rain, damp places, places with water, or places where water or oil is likely to enter the bending machine. Moisture will reduce the insulation of the motor, resulting in an electric shock accident.

2 In order to prevent an electric shock accident, please use the power supply through the leakage circuit breaker. In addition, in addition to double insulation, be sure to install a correct ground 'ground'.

3. When using it in the outer frame of pipes, heating appliances, microwave ovens, water tanks, etc., do not let your body touch the grounding 'ground wire'.

4. Please fully keep the workbench and workplace bright, and always pay attention to cleaning and rectification. Scattered places will become the fuse that causes accidents.

5. The bending machine may have rectification sparks during use, and sparks will also occur when the switch is opened and closed. Because it is dangerous to work in places where there are paints, coatings, volatile oils, gasoline, gas, adhesives, etc. that may cause flammable and explosive substances, please never use it. At the same time, be sure to stop using it in closed rooms, tunnels and other places without ventilation.

6. For safety, please wear a helmet and safety shoes with rubber soles.

7. Please use protective goggles to protect your eyes during operation. In addition, in dusty occasions, please use a dust mask and a dust collector at the same time.

8. For the installation of the bending push block and accessories, please use the method of stop gauge at the regular position and use the specified tool to correctly carry out. At the same time, the installed cover and bolts have their own important functions, please do not remove them.

9. Before inserting the plug into the power supply, please confirm whether the switch is disconnected to prevent the bending machine from starting suddenly.

10. Do not transport the bending machine when the plug is connected to the power supply. Do not hang clothes on the switch, it is easy to close the switch by mistake, which will cause an accident.

11. Please always pay attention to the soles of your feet and work in a stable posture. Working in an inappropriate state will bring danger.

12. When the bending machine is found to be in bad condition or abnormal during use, please stop the operation immediately and carry out maintenance.

13. Do not use the bending machine and its accessories beyond the scope of its use, and do not perform excessive operations. Improper operation will not only cause damage to the bending machine, but also be dangerous, please avoid it.

14. When the bending machine is running, please never touch the bending push block and the rotating part, and keep your hands and face away.

15. In order to use it safely and efficiently, please conduct regular inspections. If you need to repair, please do not hand the bending machine to someone who does not have repair knowledge and skills, so please go to the store where you purchased it for inspection and repair. Also, be sure to use the specified parts when replacing parts.

　

　
http://topseller365.com/data/prd/190/252/10.jpg

Notice:

　

1. Please use the bending machine with caution. If there is a drop or collision, the frame may be deformed, cracked or damaged. Be sure to fully check before use, and then use it after confirming safety. When it is confirmed that there is an abnormality, please check it immediately.

2. Carrying the product by the lead or pulling the lead out of the socket will damage the lead, resulting in disconnection or short circuit. At the same time, be careful not to let the lead wire come into contact with blades, high-temperature objects, chemicals, etc. If the lead wire is damaged, please stop the operation immediately and carry out inspection.

3. The fan of the bending machine is a necessary part to cool the motor, please do not block it with dust. If it is blocked, it will burn out due to excessive temperature.

4. Please clean up the machine frequently and keep it in the best condition. Especially the motor parts and switch parts, wipe the dust before each use. Also, always clean the lead wire to prevent it from deteriorating due to the action of oil or oily substances.

5. Please check the push block frequently so that it is always used in good condition.

6. This machine has a motor part, so please do not use it in rain or snow.

7. Be sure to tighten the bolts and nuts after every 300-500 bends. Especially the bolts of the sealing part between the head frame and the cylinder block.

8. Please keep the bending machine and accessories in the following places:

A. Places out of reach of children.

B. Places where temperature and humidity do not change drastically.

C. Avoid rain and places with high humidity.

D. Places out of direct sunlight.

E. Avoid placing it in places prone to fire or explosion and volatile substances.

　
http://topseller365.com/data/prd/190/252/14.jpg
http://topseller365.com/data/prd/190/252/16.jpg

WQJ-22configuration list

25

Manual valve screw

1

51

Cylinder spring (bending machine)

1

serial number

name

quantity

26

Hexagon socket head screw M5*30

4

52

Filler plug/combination gasket

1

1

Curved head frame

1

27

O-ring 9*1.9

2

53

Miniature muffler BSLM

1

2

Bend push block

1

28

Rotary valve shaft

1

54

Cylinder (bending machine)

1

3

Hexagon socket head bolt M5*10

1

29

Bending torsion spring

1

55

Hexagon socket head screw M5*80

4

4

spring pad D5

1

30

oil return handle

1

56

Cylinder piston guide shaft (bending machine)

1

5

Hexagon socket head bolt M6*30

14

31

O-ring 10*1.9

2

57

Skeleton seal 25*15*7

1

6

O-ring D70*1.9

1

32

Oil return valve seat

1

58

Deep groove ball bearing 6002-2RS

1

7

Dust ring DH28

1

33

O-ring 73*1.9

1

59

rotor

1

8

Sealing ring UN28

1

34

pump core

5

60

Self-tapping screw ST4.2*65

2

9

Hexagon socket head bolt M6*10

4

35

Pump body long spring

5

61

stator

1

10

Auxiliary handle

1

36

Drain valve

5

62

motor case

1

11

Bending Shafts (16)

1

37

Pump body short spring

5

63

Gasket

2

12

Bend Large Spring (16)

1

38

spring seat

5

64

Motor housing bracket

1

13

nut

1

39

oil seal

5

65

Hexagon socket head screw M4*35

4

14

Sealing ring UN55

1

40

magnet

3

66

Carbon brush/brush holder assembly

2

15

Hexagonal core

1

41

Deep groove ball bearing 608-2RS

1

67

Deep groove ball bearing 608-2RS

1

16

Pressure Relief Spring (16)

1

42

Manganese steel gasket 26.8*9

1

68

Bearing housing

1

17

Steel Ball Seat (16)

1

43

Needle roller bearing 12*24*10

1

69

Self-tapping screws ST3.5*9.5

2

18

Pressure relief steel ball D5

1

44

Manganese steel gasket 26.8*15

1

70

rear handle

1

19

Combination washer D12

1

45

Retaining ring for hole

1

71

Self-tapping screw ST4.2*32

4

20

Pressure relief nut

1

46

Hexagon countersunk head screw M4*16

3

72

switch

1

21

sealing plug

2

47

Piston limit ring

1

73

capacitance

1

22

Bending machine pump body (16)

1

48

cylinder piston

1

74

Wire holster

1

23

Plug M14

1

49

Sealing ring 73*63*6

1

75

with cord plug

1

24

Combination washer D14

1

50

O-ring 32*3.5

1

76

　

　

25

sealing plug

2

52

cylinder piston

1

77

with cord plug

1

　

How to use:

1. Please place the length of the bent steel bar on the bottom of the head frame and the push block according to the required length.

2. Clamp the rebar and turn on the switch.

3. The piston moves forward, the steel bar is bent, observe the bending angle with eyes, then release the switch, the motor stops running, pull back the valve handle, and the piston retreats.

　
Details
http://topseller365.com/data/prd/190/252/5.jpg
http://topseller365.com/data/prd/190/252/11.jpg

　

After purchasing this machine, please read the manual carefully,

the relevant precautions are listed in the manual

　

Specifications

　

Voltage；220V
Power：1100W
Bending time:2-2.5s
Minimum rebar size (bent to 90°):18MM
Maximum rebar size:22MM
Net weight:16kg

　

Note: Do not use the machine to bend rebars

that exceed the maximum bending size, after

bending dozens of bars, please cool down before use!

　
http://topseller365.com/data/prd/190/252/6.jpg

　
Item include: Small Portable Portable Electric Bending Machine*1

　
Item Number: 190252

　

You can make order with no worries.
Any concerns just feel free to let us know, we'll reply in 24 hours in normal condition.
Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.