Vacuum Exposure Unit 110V
You could know more information by click the video link
Working principle
The vacuum pumping area (sizes of the rubber blanket) is 23.6”*27.6” (60*70cm), but the optimum screen exposing size is within 19.7”*23.6”*1.6” (50*60*4cm) by the outer sizes. (If your screen is oversized, please buy cautiously!)
1. Connect the power supply; Turn on the switch of “POWER”;
Two control panel random delivery
2. Set the vacuum pumping time
1) Press “VACUUM”, the left indicator light (yellow) is lit up;
2) Press “ + ” or “ – ” in the “TIME CONTROL” area to set the vacuum pumping time according to your needs.
(For first-time users, please put an empty screen in the middle of the rubber inner cavity, just set 40 seconds for test; if the pointer of the vacuum gauge could reach or pass the middle of the green area, that’s ok. If not, please extend the time and test again until having reached the requirement.
3. Set the exposure time
1)
Press “EXPOSURE”, the left indicator light (red) is lit up;
2) Press “ + ” or “ – ” in the “TIME CONTROL” area to set the
exposure time according to your needs.
4. Once finished the above settings, you could start exposure just as follows
| 1) Put the screens coated with
photosensitive emulsion and the printed transparency film on the
glass. 2) Put the air suction pipe in to the screen; 3) Close the cover and click the “START” button, then it will vacuum pump and expose automatically according to the settings; 4) When the set time is up, it will deflate automatically; Open the cover and exposure is finished. Please just cut off the power supply |
5. Functions of other keys
| 1) “RESET” for cancelling the
previous settings: if you want to reset the vacuum / exposure
time, just press “VACUUM” / “EXPOSURE” and the left indicator
light is lit up; Then press “RESET” and the original settings
will turn to “ 0 ”; Next, you could set according to your needs.
2) “BACK” for stop working: if you want to stop vacuum pumping or exposure, just press the “BACK” button, that’s ok.
|
1. If the digit was not displayed once turned on the switch
a. Please check whether the power supply is good or not
b. Please check whether the bottom fuse wire is loose, burned-out or not
2. If the vacuum pump didn’t work after putting the screen on the glass, closing the cover and pressing the “STRAT” button:
Please check whether the leading wire of the vacuum pump is well connected or not
3. If it didn’t reach the requirement even the vacuum pump works well
a. please checks whether the air suction pipe is well fastened or not
b. Please check whether the rubber blanket and its edgings were good and seal or not.
If there were some splits on the rubber blankets or edgings, or some cracks of the edging adhesives, please fix them up with the sealing adhesive.
4. If the lamps were not lit up
a. Please check whether your voltage was too low or not
b. Please check whether the lamp ends were blackened or not caused by lamp ageing
c. Please check whether your set exposure time was 0 second
d．Please check whether the ballast was broken or not.
1) Please cut off the power supply when you need to change the lamp or the ballast
2) Avoid contact with hard objects to prevent glass surface scratching
3) Consistent cleaning is needed according to your using frequency and operational environment, especially for the glass, vacuum rubber blanket and edgings
Essential Parameters
· Input Voltage: 110V
· Exposure area: 23.6”*27.6” (60*70cm) (Optimum screen exposing size is within 19.7”*23.6”*1.6” (50*60*4cm) by the outer sizes.)
· Vacuum Degree: －0.08Mpa
· Illumination Uniformity: 85%
· Lamp Power: 240W
· Vacuum Pump Power: 60W
· Vacuum Time Setting Range: 0-999s
· Exposure Time Setting Range: 0-999s
· Machine Size: 33.5”*32.5”*7.5” (85*82.5*19cm)
· Package size: 35”*33.5”*9.8” (88*86*24.5cm)
· Net weight: 66Lb / 30kg
· Gross weight: 90.4Lb / 41kg
|
|
Item# |
Description |
QTY |
Unit |
Note |
|
219104 |
Vacuum Exposure Unit |
1 |
set |
Default Voltage is 110 V |
