220V Wood pellet machine 6MM
The small biomass processing pellet machine is extremely outstanding in terms of energy conservation and efficiency. It has unique effects and environmental benefits, and can turn straw and waste into treasure. It helps us solve the problem of storing or treating agricultural and forestry waste such as corn straw scales, cotton stalks, wood bran, wood powder, sawdust, peanut shells, rice husks, etc.
This machine uses waste wood to make fuel, which can replace gas and natural gas. Moreover, the fuel incineration displacement is lower, making it more environmentally friendly.
Note:
1. This machine is 220V three-phase, please pay attention to wiring issues when using it.
2. Before starting the machine,open the upper shell of the particle machine to determine if the nut above the pressure roller is secure. If there is any looseness, use a wrench to tighten it.
3. After connecting the power supply, turn on the machine to check if the rotation direction of the pressure roller is correct (counterclockwise direction).
4. Before starting the machine, please check whether the oil level inside the box meets the requirements and ensure that it is at the normal oil level (two-thirds of the oil mirror).
5. Check the oil temperature after 10 minutes of load operation, and the temperature rise should not exceed 50 ℃.
6. Please carry out daily maintenance and do not accumulate dust and oil stains on the outer frame of the gearbox to avoid affecting heat dissipation.
7.Remove the rubber ring from the brass vent nut before starting.
8.Replace the LCKC150#200# gear oil after 500 hours of use for the first oil change.
| voltage： | 220V three-phase electricity |
| Power: | 7500W |
| Production: | 60KG |
| Wood chip particle combustion value: | 3000-4300 kcal/kg. |
| Feed hopper inside diameter: | 11in(28cm) |
| Feed hopper outside diameter: | 12.2in(31cm) |
| Outlet size: | 8.86in*6.1in(22.5*15.5cm) |
The machine adopts the design of enlarged feed port, which makes it more convenient for you to feed and effectively improves work efficiency.
Before using the machine, please remove this flat 8-shaped rubber ring to avoid oil leakage.
Precautions:
1.When using, it
should be noted that there should be no foreign matter such as stones
and ironblocks in the raw materials. After the pellet machine has been
working continuously for morethan ten shifts, the pressure roller oil
hole, the universal joint oil hole, and the linkage shaft oilhole need
to be filled with high-temperature lubricating grease to make the
pressure roller Goodworking performance and extended bearing life.
2.During granulation, it is strictly forbidden for the pressure roller
to contact with the templateto run idly, and the continuous feeding can
not be interrupted.At the same time, the pressureroller shaft nut is
locked to avoid loosening and damaging the spindle keyway.
3.When granulating, there is no granulation, no discharge, the
template should be removed, andafter opening one by one, some fiber feed
can be added appropriately to restart the granulation.
4.Always
check the tightness of the screws in each part of the machine.
5.When the pellet machine is working, do not reach into the feeding
port with your hands. Ifnecessary, use wooden sticks to help feed the
pellets.
6.Before turning on the machine, it is necessary to add less material
before turning on the
machine. When shutting down, leave a small amount
of feed in the machine to prevent the pressroller of the machine from
contacting the template from idling.
7.If the machine is stuck in operation, stop it immediately, press the
pressure roller until thebolt is flat,and then restart the machine.
The particles made of wooden raw materials have varying calorific values depending on the type of wood used, mainly determined by the raw materials. At present, the main raw materials for wood particles on the market are poplar, pine, miscellaneous wood, elm, oak, apple wood, jujube wood, camphor pine, mahogany, and other wooden materials. Hardwood wood is hard and produces the highest calorific value of products, such as pine, camphor pine, mahogany, and other soft wood processed products such as poplar miscellaneous wood and tung wood are generally low in calorific value!
Product display:
You can make order
with no worry.
Any concerns just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost.